BDC Carby kits manfacture

mcbob · Post by **mcbob** » Tue Jul 14, 2009 8:37 pm

Well fellas plans are in motion to try to get a supplier manufacturer out of China who will reproduce carby diaphrams and metering side diaphrams for the range of petrol and alky use in the BDC Carbs ............. i see BDC Carb kits making stupid prices on Ebay so there's a need for a supplier ...... man i'm not gonna pay up to $100-00 bucks US for a single carb kit thats stupity.

I have and now await responces from the land of the great wall.

Wish me luck.
If this sounds a reasonable suggestion or if some-one else is making plans to do the same then please let me know

Mc Bob.

Ronald Cubel · Post by **Ronald Cubel** » Wed Jul 15, 2009 1:18 am

Have you looked at Certified parts corporation under snowmobile carb rebuild kits. Alot of walburo stuff there.

I have found ebay to not be the best place for carb parts?

Sorry if I am wrong being I do not use these carbs but it was just a thought for a place to get some of your gaskets and diaphrams.

Ron

http://www.certifiedpartscorp.com/

mcbob · Post by **mcbob** » Wed Jul 15, 2009 1:47 am

Thanks Ron that will save me chasing all over china.

Mc Bob.

Post by **Jeff Campbell** » Wed Jul 15, 2009 10:11 am

Sources for all your Mac Carb needs:

For small flatback carb diaphrams, and BDC fuel pump diaphrams contact: Perry Blair or Vince Hughes

The BDC double pumper diaphrams/gaskets are still made today for snowmobiles, be careful you only want the WDA-1 walbro replacement parts, these kits have the highest quality and are correct from what I have seen (the full rebuild WDA-1 kit contains some other parts not used in the big Mac carb, toss them). Note that there are 2 Teflon fiber reinforced pumper diaphrams (light colored with the 3 check valve flappers), DO NOT use the kits that have a black material for these diaphrams (the ones I saw at Certified parts are these ones), it is a flimsy material and the check valve flappers get sucked into the carb plate holes >> bad news! These kits are low in price. I use these in all my Mac double pumpers:

Jeff

mcbob · Post by **mcbob** » Wed Jul 15, 2009 4:49 pm

Looks as if the 07-410-2 is the one i need as these are double pumper kits and the only bits i use are the main diaphram and the small gasket that goes under the plate in the bottom of the chamber i have quite a few of the flapper gasket or diaphram.

I did a couple of years ago get some double pumper kits off Tired Iron but i only needed the main diaphram and the small gasket.

Anyway i'll chase some up today and get them under way to OZ.

McBob.

Post by **Jeff Campbell** » Wed Jul 15, 2009 8:30 pm

Bob,
I think this is the same main diaphragm that goes in the WDA-1 kit, look closely...

Jeff

mcbob · Post by **mcbob** » Wed Jul 15, 2009 9:06 pm

Jeff Campbell wrote:Bob,
I think this is the same main diaphragm that goes in the WDA-1 kit, look closely...

Jeff

Thanks Jeff thats the baby .................... Mc Bob.

John Miller · Post by **John Miller** » Wed Jul 15, 2009 10:25 pm

How do these kits compare to the parts/kits that EC Distributing sells?

BDC Carby kits manfacture

BDC Carby kits manfacture

Re: BDC Carby kits manfacture

Re: BDC Carby kits manfacture

Re: BDC Carby kits manfacture

Re: BDC Carby kits manfacture

Re: BDC Carby kits manfacture

Re: BDC Carby kits manfacture

Re: BDC Carby kits manfacture