There were a few cast manifolds for WB / HR setup's but they are very hard to come by.
GEM V12 or V6 stuffer would also be other options.
Search found 1530 matches
- Sun Feb 15, 2009 1:15 pm
- Forum: General Discussion
- Topic: looking for way to adapt HR carb to west bend 820
- Replies: 5
- Views: 5500
- Mon Feb 02, 2009 7:23 pm
- Forum: General Discussion
- Topic: Tillotson carb for MC-91A
- Replies: 7
- Views: 7484
Re: Tillotson carb for MC-91A
As a side note, does anyone know when HR178's came out or what they were used on? I have a couple and they are alky carbs and work well.
- Mon Feb 02, 2009 2:23 pm
- Forum: General Discussion
- Topic: Tillotson carb for MC-91A
- Replies: 7
- Views: 7484
Re: Tillotson carb for MC-91A
Harold Member I thought you were going to leave. Don't let the door hit ya on your way out.
- Mon Feb 02, 2009 9:18 am
- Forum: General Discussion
- Topic: Tillotson carb for MC-91A
- Replies: 7
- Views: 7484
Re: Tillotson carb for MC-91A
If you want to run a HL series (smaller, maybe for a youngster or very early kart) carb on the engine you can get a different manifold & reed cage and use that also. Over the years there is a variety of sizes available that should suit your needs. The HR series works great. Lots of HR181 & HR191 car...
- Wed Jan 28, 2009 7:18 pm
- Forum: General Discussion
- Topic: Cleaning blocks and aluminum parts
- Replies: 12
- Views: 11317
Re: Cleaning blocks and aluminum parts
NAPA carb cleaner. They make a quart size for small carbs and a 5 gallon for blocks. Works great nad washes off with water.
- Tue Jan 27, 2009 8:26 am
- Forum: General Discussion
- Topic: Cleaning blocks and aluminum parts
- Replies: 12
- Views: 11317
Re: Cleaning blocks and aluminum parts
I have a dip tank for carbs that do a great job cleaning. Then get it plastic beaded. MAKE SURE they use clean plastic.
- Mon Jan 26, 2009 2:18 pm
- Forum: General Discussion
- Topic: mystery kart w/mc6
- Replies: 5
- Views: 5256
Re: mystery kart w/mc6
I would guess it is a home built or modified quarter midget. Front axle looks 1/4 midget. Narrow front looks quarter midget. Back end looks modified from the floating back end that quarter midget's used to use.
- Sun Jan 25, 2009 7:34 pm
- Forum: General Discussion
- Topic: gk800 questions
- Replies: 2
- Views: 3110
Re: gk800 questions
I'm sure Jeff Troy or someone will post a picture. I sold him a Go Kart 800 frame with a sissor brake on the left rear motor mount but I forget how it was attached.
- Tue Jan 20, 2009 8:01 am
- Forum: General Discussion
- Topic: "dressing" welds on a 1961 Bug.....
- Replies: 3
- Views: 4418
Re: "dressing" welds on a 1961 Bug.....
Don't use powder coat. A frame that has a reputation to crack making future repair difficult.
I don't care for the look of ground down welds. It's hard to get into a lot of spots and do a good job. Also it will decrease the resale value.
I don't care for the look of ground down welds. It's hard to get into a lot of spots and do a good job. Also it will decrease the resale value.
- Mon Jan 19, 2009 3:26 pm
- Forum: General Discussion
- Topic: Smaller Clutch Diamater for Clinton A400
- Replies: 13
- Views: 11956
Re: Smaller Clutch Diamater for Clinton A400
I should have drums but no guts for them. They will probably be 11,12,13,14 tooth.