Search found 18 matches

by Bob Cornwell
Tue May 23, 2017 2:12 am
Forum: General Discussion
Topic: Hyperod inserts
Replies: 2
Views: 4227

Hyperod inserts

Anyone have a spare pair of inserts for the roller needles on the Mac hyperod they would care to part with if so give me a belt ........... McBob ... ozflea@hotmail.com
by Bob Cornwell
Tue Mar 28, 2017 4:06 pm
Forum: General Discussion
Topic: D-44/55 Mac saws
Replies: 14
Views: 17158

Re: D-44/55 Mac saws

Well Terry just read your post I don't mess with them there little critters i'm into big boys toys over 100cc.

So a bit of a blank here i'm afraid good luck with the D-44/55

McBob
by Bob Cornwell
Sun Mar 26, 2017 9:59 pm
Forum: General Discussion
Topic: Westbend 820 crank
Replies: 7
Views: 10378

Re: Westbend 820 crank

Ultralight motor Don't think so as then there would be nowhere to mount the prop drive boss if it used a reduction drive It's funny the shaft has been cut as now the engine is useless but in my case I bought it to get the cylinder as my old one had busted mounting bosses so now I have a few spares ...
by Bob Cornwell
Sun Mar 19, 2017 1:08 am
Forum: General Discussion
Topic: The Power Products PP58 AND 81, 82
Replies: 4
Views: 5877

Re: The Power Products PP58 AND 81, 82

Thanks Fellas
by Bob Cornwell
Thu Mar 09, 2017 11:48 pm
Forum: General Discussion
Topic: Understanding West Bend Rods
Replies: 5
Views: 6650

Re: Understanding West Bend Rods

For some reason people seem to think the rod that is shown as being the good one is some special race only part. It is the stock factory rod of today in all the USMP engines. In the days of old when People would do all the mods (they did these same engine porting mods in the 60's as are done today)...
by Bob Cornwell
Wed Mar 08, 2017 10:54 pm
Forum: General Discussion
Topic: The Power Products PP58 AND 81, 82
Replies: 4
Views: 5877

Re: The Power Products PP58 AND 81, 82

Bob, Steen's offered a adaptor plate #P27F that allowed the #P27D Dual intake manifold for a AH -58 to be used on the AH 82 engine. Not sure who the actual mfg. is on the components, could be Palmini. There were a lot of folks popping out hot rod parts in the early days so there should be something...
by Bob Cornwell
Wed Mar 08, 2017 8:43 pm
Forum: General Discussion
Topic: Westbend 820 crank
Replies: 7
Views: 10378

Re: Westbend 820 crank

Bob, Most all West Bend engines were made for industrial applications and they continue that tradition today so if the crank end was not cut or broke off you have a power plant for something other then a kart. Pretty sure the 820 was used on generators, water pumps, jaws-of-life and many other appl...
by Bob Cornwell
Wed Mar 08, 2017 8:40 pm
Forum: General Discussion
Topic: Westbend 820 crank
Replies: 7
Views: 10378

Re: Westbend 820 crank

Ultralight motor Don't think so as then there would be nowhere to mount the prop drive boss if it used a reduction drive It's funny the shaft has been cut as now the engine is useless but in my case I bought it to get the cylinder as my old one had busted mounting bosses so now I have a few spares ...
by Bob Cornwell
Wed Mar 08, 2017 8:35 pm
Forum: General Discussion
Topic: Understanding West Bend Rods
Replies: 5
Views: 6650

Re: Understanding West Bend Rods

I believe the early Copperheads and Vintage 820's weren't modded like this but are now standard
by Bob Cornwell
Thu Mar 02, 2017 8:16 pm
Forum: General Discussion
Topic: Westbend 820 crank
Replies: 7
Views: 10378

Westbend 820 crank

I bought a Westbend / US820 Power Bee with a cut off crank the leftover stub would only be 1/2" long
What was the use or reason the crank has had the PTO shaft lopped off ?