Search found 18 matches
- Tue May 23, 2017 2:12 am
- Forum: General Discussion
- Topic: Hyperod inserts
- Replies: 2
- Views: 4459
Hyperod inserts
Anyone have a spare pair of inserts for the roller needles on the Mac hyperod they would care to part with if so give me a belt ........... McBob ... ozflea@hotmail.com
- Tue Mar 28, 2017 4:06 pm
- Forum: General Discussion
- Topic: D-44/55 Mac saws
- Replies: 14
- Views: 17409
Re: D-44/55 Mac saws
Well Terry just read your post I don't mess with them there little critters i'm into big boys toys over 100cc.
So a bit of a blank here i'm afraid good luck with the D-44/55
McBob
So a bit of a blank here i'm afraid good luck with the D-44/55
McBob
- Sun Mar 26, 2017 9:59 pm
- Forum: General Discussion
- Topic: Westbend 820 crank
- Replies: 7
- Views: 10551
Re: Westbend 820 crank
Ultralight motor Don't think so as then there would be nowhere to mount the prop drive boss if it used a reduction drive It's funny the shaft has been cut as now the engine is useless but in my case I bought it to get the cylinder as my old one had busted mounting bosses so now I have a few spares ...
- Sun Mar 19, 2017 1:08 am
- Forum: General Discussion
- Topic: The Power Products PP58 AND 81, 82
- Replies: 4
- Views: 5995
Re: The Power Products PP58 AND 81, 82
Thanks Fellas
- Thu Mar 09, 2017 11:48 pm
- Forum: General Discussion
- Topic: Understanding West Bend Rods
- Replies: 5
- Views: 6755
Re: Understanding West Bend Rods
For some reason people seem to think the rod that is shown as being the good one is some special race only part. It is the stock factory rod of today in all the USMP engines. In the days of old when People would do all the mods (they did these same engine porting mods in the 60's as are done today)...
- Wed Mar 08, 2017 10:54 pm
- Forum: General Discussion
- Topic: The Power Products PP58 AND 81, 82
- Replies: 4
- Views: 5995
Re: The Power Products PP58 AND 81, 82
Bob, Steen's offered a adaptor plate #P27F that allowed the #P27D Dual intake manifold for a AH -58 to be used on the AH 82 engine. Not sure who the actual mfg. is on the components, could be Palmini. There were a lot of folks popping out hot rod parts in the early days so there should be something...
- Wed Mar 08, 2017 8:43 pm
- Forum: General Discussion
- Topic: Westbend 820 crank
- Replies: 7
- Views: 10551
Re: Westbend 820 crank
Bob, Most all West Bend engines were made for industrial applications and they continue that tradition today so if the crank end was not cut or broke off you have a power plant for something other then a kart. Pretty sure the 820 was used on generators, water pumps, jaws-of-life and many other appl...
- Wed Mar 08, 2017 8:40 pm
- Forum: General Discussion
- Topic: Westbend 820 crank
- Replies: 7
- Views: 10551
Re: Westbend 820 crank
Ultralight motor Don't think so as then there would be nowhere to mount the prop drive boss if it used a reduction drive It's funny the shaft has been cut as now the engine is useless but in my case I bought it to get the cylinder as my old one had busted mounting bosses so now I have a few spares ...
- Wed Mar 08, 2017 8:35 pm
- Forum: General Discussion
- Topic: Understanding West Bend Rods
- Replies: 5
- Views: 6755
Re: Understanding West Bend Rods
I believe the early Copperheads and Vintage 820's weren't modded like this but are now standard
- Thu Mar 02, 2017 8:16 pm
- Forum: General Discussion
- Topic: Westbend 820 crank
- Replies: 7
- Views: 10551
Westbend 820 crank
I bought a Westbend / US820 Power Bee with a cut off crank the leftover stub would only be 1/2" long
What was the use or reason the crank has had the PTO shaft lopped off ?
What was the use or reason the crank has had the PTO shaft lopped off ?